Furnace repair in Denver
Denver heats for five months, and the furnace usually works hardest on the first cold night, after six months of rest. When it fails, the cause is rarely dramatic: a dirty flame sensor, a clogged filter, a frozen condensate line, a thermostat that lost its settings. What matters is whether the person who comes can tell which one it is.
What a real heating call covers
A furnace runs through a sequence: the thermostat calls, the draft inducer starts, a pressure switch confirms the flue is clear, the igniter lights, the gas valve opens, a flame sensor proves a flame, and only then does the blower move air. A failure at any step shuts the whole thing down, and the fault code or the point where the sequence stops tells a technician which step to look at. A call that skips straight to “you need a new board” has skipped the diagnosis.
The most common culprits are small and inexpensive: a flame sensor coated with residue that needs cleaning, an igniter that has cracked, a pressure switch tube that has clogged, a filter that has choked the airflow until the high-limit switch shuts things down. A good call fixes the actual cause and tells you what else it saw while it was looking.
What altitude changes
At Denver’s elevation, gas has less oxygen to burn with. Furnaces are rated for sea level unless they are set up for altitude, and most manufacturers publish a derating rule, on the order of four percent for every thousand feet above two thousand feet, which works out to well over ten percent here. Depending on the model, that means different burner orifices, a pressure adjustment or an altitude kit. A furnace that was installed without that attention can run sooty, short-cycle or overheat, and the symptoms look like ordinary equipment trouble.
Any provider who works on gas equipment in the metro should be able to say what altitude the furnace is set for, and show the manifold pressure they measured. If the answer is a shrug, ask for it in writing before the work.
Basements, flues and safety
In many Denver houses the furnace sits in a basement closet or a mechanical room shared with the water heater. That puts combustion air, flue condition and carbon monoxide at the center of the call. A provider should check the flue for draft and corrosion, the heat exchanger for cracks where it can be seen, and the room for enough air to burn properly. A carbon monoxide detector on every level is a basic safety measure, and one that should be tested when the clocks change.
Furnace repair questions, answered plainly
- Why does my furnace start and then shut off?
- The usual causes are a dirty flame sensor that cannot prove a flame, a clogged filter that trips the high-limit switch, or a blocked flue pressure switch. Each has a different fix, which is why the point where the sequence stops matters.
- Does my furnace need to be set for altitude?
- Yes. Denver’s elevation reduces the oxygen available to burn gas, so gas furnaces need the manufacturer’s high-altitude settings or kit. Ask what elevation your furnace is set for.
- Why does my high-efficiency furnace keep lighting and failing?
- High-efficiency models produce condensate that drains through a small line. In a cold basement or garage that line can freeze or clog, and the furnace locks out to protect itself.
- Should I repair or replace a 20-year-old furnace?
- A furnace that old is near the end of its usual range, so a modest repair can be reasonable but a major one, like a cracked heat exchanger, usually is not. Ask for both options in writing.
- 1 Thermostat: It decides when everything starts. In April it can call for heat at dawn and cooling by afternoon.
- 2 Return and filter: Where the house breathes in. Dry Front Range air clogs it faster than most owners expect.
- 3 Furnace: In a basement closet, idle for six months, then asked for everything on the first cold night.
- 4 Coil and condensate drain: Ice in July if airflow drops, a frozen drain line in January if the route crosses a cold corner.
- 5 Basement ducts: Sheet metal through the joists and up old chases, with leaks in places nobody visits.
- 6 Outdoor unit: Thin air, cottonwood fluff in June and a long dry spell: less margin than the label implies.